manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 6 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 6

Problem-free and safe operation of the product depends on the following:

•

Proper transport

•

Proper storage, setup and installation

•

Proper operation and maintenance

When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper
action is not taken, death, severe injury or property damage can result:

•

The equipment must be grounded at the grounding terminal before any connections are made.

•

All circuit components connected to the power supply may be subject to dangerous voltage.

•

Hazardous voltages may be present in equipment even after the supply voltage has been disconnected
(capacitors can still be charged).

•

Operation of equipment with exposed current-transformer circuits is prohibited. Before disconnecting the
equipment, ensure that the current-transformer circuits are short-circuited.

•

The limiting values stated in the document must not be exceeded. This must also be considered during
testing and commissioning.

Selection of Used Symbols on the Device

Nr.

Symbol

Description

1

Direct current, IEC 60417, 5031

2

Alternating current, IEC 60417, 5032

3

Direct and alternating current, IEC 60417, 5033

4

Earth (ground) terminal, IEC 60417, 5017

5

Protective conductor terminal, IEC 60417, 5019

6

Caution, risk of electric shock

7

Caution, risk of danger, ISO 7000, 0434

8

Protective Insulation, IEC 60417, 5172, Safety Class II devices

9

Guideline 2002/96/EC for electrical and electronic devices

10

Guideline for the Eurasian Market

OpenSSL

This product includes software developed by the OpenSSL Project for use in OpenSSL Toolkit (

http://

www.openssl.org/

).

This product includes software written by Tim Hudson (

[email protected]

).

This product includes cryptographic software written by Eric Young (

[email protected]

).

Preface

SICAM, SICAM P850/P855 7KG85X, Manual

5

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments