manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 247 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 247

Technical Data

Power Supply

Direct Voltage

Rated input voltages

24 V to 250 V

Admissible input voltage tolerance

±20 %

Permitted ripple of the input voltage

15 %

Maximum inrush current
At ≤ 110 V

< 15 A

At 220 V to 300 V

≤ 22 A; after 250 μs: < 5 A

Maximum power consumption

5 W

Alternating Voltage

Rated input voltages

110 V to 230 V

System frequency at AC

50 Hz/60 Hz

Admissible input voltage tolerance

±20 %

Permitted harmonics

2 kHz

Maximum inrush current
At ≤ 115 V

< 15 A

At 230 V

≤ 22 A; after 250 μs: < 5 A

Maximum power consumption

16 VA

Inputs and Outputs

Inputs for Alternating Voltage Measurements, Connector Block F - Cat III

Rated input alternating voltage range
Phase-N/PE

63.5 V
110 V
230 V
400 V (347 V for UL)

Phase-phase

110 V
190 V
400 V
690 V (600 V for UL)

Maximum input alternating voltage
Phase-N/PE

480 V (347 V for UL)

Phase-phase

831 V (600 V for UL)

Input impedances
a, b, c to N

6.0 MΩ

a-b, b-c, c-a

6.0 MΩ

Further information about the voltage measuring inputs
Power consumption per input for V

rated

 400 V

38 mW

Permissible power frequency

42.5 Hz to 69.0 Hz

Measuring error (with calibration) at 23 °C ± 1 °C 50
Hz or 60 Hz

Typically 0.1 % under reference conditions

12.1

12.1.1

12.1.2

Technical Data
12.1 Technical Data

246

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments