manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 5 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 5

90459 Nuremberg

Internet:

www.siemens.com/poweracademy

Germany

Notes on Safety

This document is not a complete index of all safety measures required for operation of the equipment (module
or device). However, it comprises important information that must be followed for personal safety, as well as
to avoid material damage. Information is highlighted and illustrated as follows according to the degree of
danger:

!

DANGER

DANGER means that death or severe injury will result if the measures specified are not taken.

²

Comply with all instructions, in order to avoid death or severe injuries.

!

WARNING

WARNING means that death or severe injury may result if the measures specified are not taken.

²

Comply with all instructions, in order to avoid death or severe injuries.

!

CAUTION

CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken.

²

Comply with all instructions, in order to avoid moderate or minor injuries.

NOTICE

NOTICE means that property damage can result if the measures specified are not taken.

²

Comply with all instructions, in order to avoid property damage.

i

i

NOTE

Important information about the product, product handling or a certain section of the documentation
which must be given attention.

Qualified Electrical Engineering Personnel

Only qualified electrical engineering personnel may commission and operate the equipment (module, device)
described in this document. Qualified electrical engineering personnel in the sense of this document are
people who can demonstrate technical qualifications as electrical technicians. These persons may commission,
isolate, ground and label devices, systems and circuits according to the standards of safety engineering.

Proper Use

The equipment (device, module) may be used only for such applications as set out in the catalogs and the
technical description, and only in combination with third-party equipment recommended and approved by
Siemens.

Preface

4

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments