Siemens SICAM 7KG85X Manual Download Page 76

Page: 76 / 281

Parameter

Default Setting

Setting Range

Parity

Even

None, 1 stop bit
Even
Odd
None, 2 spot bit

Access rights

Full

Full
Read only

Communication supervision
time

600 * 100 ms

0 s = none
100 ms to 6 553 400 ms

•

After the parameterization, click Send.

•

In the navigation window, click Activation and cancel.

•

Enter the activation password (refer to

Table 2-3

•

Click Activation.

Configuration via Display

Submenu Modbus RTU (Slave) Settings

The operation is carried out with the softkeys F1 to F4.

[dw_submenu_serial_communication_p85x, 1, en_US]

Figure 2-36

Submenu Communication via Modbus RTU Slave

Table 2-22

Settings for Communication Serial, Modbus RTU (Slave)

Parameter

Default Setting

Setting Range

Bus protocol

Modbus RTU

None
Modbus RTU

(slave)

IEC 60870-5-103

Device address

1 to 247

Baud rate

19 200 bit/s

1200 bit/s, 2400 bit/s,
4800 bit/s, 9600 bit/s,
19 200 bit/s, 38 400 bit/s,
57 600 bit/s, 115 200 bit/s

Parity

Even

None, 1 stop bit
Even
Odd
None, 2 spot bit

Access rights

Full

Full
Read only

Communication supervision
time

600 * 100 ms

0 s = none
100 ms to 6 553 400 ms

2.7.1.3

Basic Functions

2.7 Serial Communication

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Search results

Summary of Contents for SICAM 7KG85X

Reviews:

Siemens SICAM 7KG85X, Manual, Page: 76 / 281

Search results

Summary of Contents for SICAM 7KG85X

Reviews: