manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 193 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 193

Assembly

General Assembly Notes

Depending on the model, SICAM P850/P855 is designed either for panel flush mounting (device with display)
or for DIN rail assembly (device without display).

!

WARNING

Do not touch any live parts.
Non-observance may lead to death or serious injury.

²

After installation of the device and wiring, close the control cabinet.

•

The installation site must be vibration-proof. The permitted ambient temperature must be observed (see
also chapter 

12 Technical Data

).

•

Operating the device outside the permitted operating temperature range can lead to measuring errors
and device failure.

•

The terminals are designed for wire cross-sections of max. 2.5 mm

2

.

•

The device must not be exposed to condensation during operation.

•

Install the device in a location where it is not exposed to direct sunlight and strong temperature varia-
tions.

Assembly: Devices with Display for Panel Flush Mounting

To install the device into a switch panel, proceed as follows:

9.3

Commissioning and First Steps
9.3 Assembly

192

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments