manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 25 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 25

Device Design

Mechanical Design

The electrical modules are installed in a plastic case with the dimensions (W x H x D) 96 mm (3.78 inch) x 96
mm (3.78 inch) x 100 mm (3.94 inch).
In panel flush mounting devices, the display side accommodates the display, 4 softkeys located below, and 4
LEDs of which the H1, H2, and ERROR LEDs can be parameterized. The ERROR LED can only be parameterized
for error messages.
The device top side holds the RJ45 Ethernet plug connector with 2 LEDs. 4 additional LEDs are identical to the
LEDs on the display side. At the cover of the battery compartment there is a labeling strip for the configurable
LEDs H1/H2 and a battery symbol that indicates the polarity. The label is also located on the top side and
provides among other information the most important rated data of the device. A lithium battery is located
under the removable cover of the battery compartment.
The device can also contain a D-sub connector plug as RS485 interface (see 

Figure 1-8

).

[le_P85X_front side, 1, --_--]

Figure 1-7

Layout of P850/P855 – Front Side

(1)

LED RUN

(2)

LED ERROR for error configuration

(3)

Battery compartment

(4)

RJ45 with 2 LEDs

(5)

Display

(6)

Default IP address and default subnet mask

(7)

LED H1 for free configuration

(8)

Softkeys F1 to F4

(9)

LED H2 for free configuration

1.3

Introduction
1.3 Device Design

24

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments