Siemens OZW775 Basic Documentation Download Page 9

Page: 9 / 120

9/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

KNX (Konnex) and Synco

30.08.2007

S-mode is characterized by the assignment of (logical) group addresses to
individual

data points to create the communications bindings for the exchange of

process values. Devices bearing the same group address exchange process
values with each other.

The group addresses can be assigned to the group objects (S-mode data points)
with the

ETS

engineering and commissioning tool

(

ETS = Engineering Tool

Software)

For the various HVAC, lighting and security equipment and for integration into
higher-level building automation and control systems, selected data points of the
Synco devices can also communicate in S-mode.

"Data points" are also referred to as "communication objects".

Description

Area coupler (see section 1.4)

DPSU

Decentral Power Supply Unit (see section 2.2.1)

E-Mode

Easy-Mode, LTE-mode is one of several "Easy Modes"

ETS

Engineering Tool Software

HVAC

Heating, Ventilation and Air Conditioning

Internet Protocol

Line coupler (see section 1.4)

LTE-Mode

Logical Tag Extended Mode, the Easy Mode used by Synco

KNX

Communications standard (wired) TP1 (Twisted Pair)

PSU

Power supply unit, (see section 2.2.3)

S-mode

System mode, configuration / commissioning with ETS only

TP1

wisted

air

, data transfer medium: bus

S-mode

Group addresses

Data points

Abbreviations

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands