Siemens OZW775 Basic Documentation Download Page 27

Page: 27 / 120

27/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Commissioning notes

30.08.2007

Select "Off" on the "Preselection" line and confirm by pressing the OK knob.

Press ESC to return to the "Main menu" page.

Select "Commissioning" and press the knob.

Before the "Commissioning" page is displayed, the following warning appears:

Confirm the display of

by pressing the knob (this causes the plant to stop). The

"Commissioning" page now appears.

Select the "Communication" line for example, by rotating the knob, and then press
the knob to open the "Communication" page.

Main menu > Commissioning > Communication

Press the knob for access to the "Basic settings" page

Plant operation = Off

Action

Return to main menu

Action

Plant stopping

Action

Communication

Action

Commissioning

Basic configuration...

Extra configuration...

Settings...

Communication...

Communication

Basic settings...

Room...

Holidays//Special days...

Distribution zones...

Caution!

Plant stops

ESC

Plant operation

Preselection: Off

State: Off

Cause: Plant op. selector

Main menu

Commissioning...

Time switch...

Room operating mode...

Plant operation...

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands