Siemens OZW775 Basic Documentation Download Page 50

Page: 50 / 120

50/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

= Parameter mode

(continued)

Press

+/–

to find a new parameter number and confirm with

(Enter). The

value concerned is then displayed.

Press

+/–

to change the value and confirm with

(Enter).

Press

(Esc) to return to the parameter number level without making any

changes.

Press > (Esc) again for access to the list mode and a third time for access
to the normal (room unit) mode.

The device address or network address is set via the following parameter numbers:

P 1

Area

)

P 2

Line

)> Network address

P 3

Device address

)

The same applies to the RXB/RXL room controllers as to the Synco bus devices,
i.e. the area and line address is adopted by the super-ordinate area/line couplers.

When setting the area/line address via the room unit, take care not to reprogram
any valid addresses.

Modifiable parameters
in parameter mode

Notes

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands