Siemens OZW775 Basic Documentation Download Page 94

Page: 94 / 120

94/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Appendix

30.08.2007

9.1.2 Communication

errors

The following is a list of errors associated with communication over the KNX bus
(see also the listed sections in this document).

Fault No.

Fault message on
RMZ79x operator unit

Type of failure

5000

No bus power supply

5001

System time failure

System time failure (slave)

5101

Time swi fail pl 1

Time switch program failure (plant 1)

5111

Time swi fail pl 2

Time switch program failure (heating circuit 2)

5201

Hol/spec day failure

Failure holiday/special day program

5301

DHW time swi fail

DHW time switch program failure

5401

Room mast fail pl 1

Room master failure (plant 1)

5411

Room mast fail pl 2

Room master failure (heating circuit 2)

Fault No.

Fault message on
RMZ79x operator unit

Setting errors

6001

>1 id device address

More than one device with identical device address

5002

>1 clock time master

More than one clock time master

5102

>1 time switch pl 1

More than one time switch program active in same zone
(plant 1)

5112

>1 time switch pl 2

More than one time switch program active in same zone
(heating circuit 2)

5202

>1 hol/sp day prgm

More than one holiday/special day program active in the
same day/special day zone

5302

>1 DHW time switch

More than one time DHW switch program active in same
zone

5402

>1 geogr zone [1]

More than one controller operating as room master in the
identical geographical zone [1]

5412

>1 geogr zone [2]

More than one controller operating as room master in the
identical geographical zone [2] (e.g. RMH: heating circuit 2)

Failure

Setting errors

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands