Siemens OZW775 Basic Documentation Download Page 12

Page: 12 / 120

12/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

KNX (Konnex) and Synco

30.08.2007

1.3

The KNX network

1.3.1 Full-scale

KNX

network

A full Konnex network is structured on three levels. It consists of:

•

Area line

Area 0 (backbone line)

•

Main lines

1...15

Areas 1…15

•

Lines

1.1...15.15

e 1

e 2

e 3

e 1

e 2

e 3

1.0.0

1.1.0

1.2.0

1.3.0

1.15.0

Area 1

Main line 1

0.1.0

0.2.0

2.0.0

2.1.0

2.2.0

2.3.0

Area 2

Main line 2

3.0.0

3.1.0

3.2.0

3.3.0

3.15.0

Area 3

Main line 3

15.0.0

15.1.0

15.2.0

15.3.0

Area 15

Main line 15

lin

2.15.0

The arrangement of the bus devices in the 3-level KNX network structure, with the
Synco bus devices factory set with Area/Line address 0.2 corresponds to the gray
shaded area in the illustration above.

KNX network,
three-level structure

Note

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands