Siemens OZW775 Basic Documentation Download Page 99 | Manualshive

Page: 99 / 120

background image

99/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Appendix

30.08.2007

Main menu > Commissioning > Extra configuration > Heating/cooling changeover

Operating line

Range

Factory setting

Heating/cooling based on calendar

No, Yes

No

Main menu > Commissioning > Settings > Heating/cooling changeover

Operating line

Range

Factory setting

Start date, heating

01.01. - 31.12.

01.10.

Start date, cooling

01.01. - 31.12.

01.05.

The changeover occurs on the "Start date, heating" or "Start date, cooling".

9.2.4

H/C changeover relay and fault messages

If, instead of being transmitted over the bus, the H/C changeover signal is to be
made available at a relay output e.g. for switch control of a valve or for forwarding
to a non-communicating device, the H/C changeover relay can be configured
accordingly. See the notes on connecting the primary controller to the changeover
valve.

Main menu > Commissioning > Extra configuration > Heating/cooling changeover

Operating line

Range

Factory setting

Heating/cooling changeover relay

----, N.Q1, N.Q2,…/

----

The current contact position (status) of the changeover relay can be displayed via
the Service level.

Main menu > Heating/cooling changeover

Operating line

Current contact position (status)

Heating/cooling changeover relay

Open (Off) Cooling / Closed (On) Heating

In a 2-pipe heating/cooling system without a "Heating/Cooling changeover" signal
on the KNX bus, the controller continues to use the last received value. If the signal
never existed, then "Heating" is used as the default value.

No.

Text

Effect

5801 H/C

changeover

signal failure

Non-urgent message; no acknowledgement
required.

If the "H/C changeover" in a 2-pipe system is configured so that it is initiated by
calendar or by operating mode selector, and a changeover signal is received in one
of the zones from another device, then the fault message "> 1 heat/cool
changeover signal" is transmitted.

No.

Text

Effect

5802 >1

heat/cool

changeover signal

Non-urgent message; acknowledgement is
required.

Configuration

Settings

Heating/cooling
changeover relay

Configuration

Current contact position

Fault status messages

H/C changeover signal
failure

Fault status message
5801

> 1 H/C changeover signal

Fault status message
5802

«
...
97
98
99
100
101
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: DayTronic Pages: 414

Brand: Lathem Pages: 4

Brand: Magnavox Pages: 23

Brand: Jensen Pages: 13

Brand: N-Com Pages: 32

Brand: Coby Pages: 3

RM-208 CB.13.01

Brand: EasyLine Pages: 16

Brand: Taiden Pages: 91

Brand: Steren Pages: 26

Brand: Craig Pages: 2

Brand: Chrosziel Pages: 2

MERLIN LEGEND Release 6.0

Brand: Lucent Technologies Pages: 160

Brand: Vicon Pages: 91

Brand: Nibe Pages: 32

Brand: Boss Audio Systems Pages: 2

niagara4 MultiSITE Edge 10

Brand: LG Pages: 73

Brand: LG Pages: 29

Brand: LG Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands