Siemens OZW775 Basic Documentation Download Page 62

Page: 62 / 120

62/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Basic communication settings

30.08.2007

Clock time op.:

Auto

The RM… controller does not receive or transmit the time
or date (The device has its own time and date).

Clock time op.:

Slave

The RM… controller receives the time and date from the
time master.

Clock time op.:

Master

The RM… controller transmits the time and date in a 10
minute cycle over the KNX bus, starting from the last
time-synchronization

Sends

time of day:

10:15

Receives:

10:15

Clock time operation:
Master

Clock time operation:
Slave

Clock time operation:
Autonomous

312

37e

Receives:

10:15

Has its own

time of day

Receives:

10:15

Time of day for
timer function

The time and date in the time master can be modified as follows:

•

By the user, on the time master

•

By the user, by remote adjustment of the time slave

A user-adjustment of the time or date can be synchronized by pressing the rotary
knob.

Only one

bus device at a time can be the time master in a network. In relation to

the date and time, the other bus devices must be set as time "slaves" or set to
"Autonom."

6.1.3

Setting a time slave remotely

The operating line "Rem set clock slave" can be used to configure a time slave so
that the time and date can be set by an operator. The new values are then
transmitted via the KNX bus to the time master.

Main menu > Commissioning > Communication > Basic settings

Remote time-slave setting for RM… controller
Default.

Yes

Settings

No/Yes

Settings

Example

Modifying the
time and date

Note

Clock time operation:
Slave with
"Rem set clock slave:"

Yes

Basic settings

Device address: 1

Dec bus power supp: On

Clock time op: Slave

Rem set clock save: Yes

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands