Siemens OZW775 Basic Documentation Download Page 101 | Manualshive

Page: 101 / 120

background image

101/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Appendix

30.08.2007

QAW740

RMH...

RMH...

31

27

Z

2

8e

n

Geogr zone: 1

Room unit

Geogr zone: 1

Operating mode

Geogr zone: 1

Heating circuit 1, master

Operating mode

Heating circuit 2, slave

Room control combination

Master

Transmits room setpoint and operating mode

Room control combination

Slave, external setpoint

Receives room setpoint and operating mode

Room control combination

Slave, internal setpoint

Retains its own room setpoint as valid, but adopts the
operating mode from the master.

Room control combinations featuring multiple ventilation controllers

When a space is controlled by more than one ventilation controller (e.g. two
RMU7x0B controllers (and they must be RMU7x0B controllers) controlling the
temperature in a warehouse) the controllers can exchange information such as
room temperature, operating mode and setpoint over the KNX bus.

With this room control combination, one ventilation controller must be set as the
master and all the others as slaves.

QAW740

RMU...

RMU...

312

7Z49d

e

Geogr zone = 2

Room operating mode

Geogr zone = 2

Ventilation 1

Room control comb. =

Master

Room control comb. =

Slave ext. setpoints

Room unit

Geogr zone = 2

Room operating mode

Ventilation 2

Within the room control combination, the slave ventilation controllers operate with
the same operating mode as the master.

The slave controllers can use either the same setpoints as the master, or individual
setpoints.

Zone addressing

Setting the room control
combination

Application example 2

Note

Zone addressing

Settings for the slave
ventilation controller(s)

«
...
99
100
101
102
103
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: Lathem Pages: 4

Brand: GSK Pages: 32

Studio 500 Series

Brand: JAMO Pages: 16

Brand: Edin Pages: 20

bryant ONEBB3ZAC01

Brand: Carrier Pages: 6

Brand: Steren Pages: 12

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 15

Brand: TDK Pages: 9

Brand: Okuma Pages: 109

Brand: Bosch Pages: 32

Rexroth CC-CS351

Brand: Bosch Pages: 96

Brand: Bosch Pages: 10

LTC 8808/00 Series

Brand: Bosch Pages: 108

Security Escort SE2000 Series

Brand: Bosch Pages: 248

Brand: Bosch Pages: 243

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands