Siemens OZW775 Basic Documentation Download Page 36

Page: 36 / 120

36/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

The "Edit device list" dialog box displays the device list with the existing devices.

Description of the columns in the "Edit device list" dialog box.

Column

Description.

Device Name

Device names can be entered together with the network address. If no
device name is entered, the display reads: Device address n

Network address

Area.Line.Device Address

Unique factory-set KNX serial number

Type

Device type, e.g. RMU730. "Default" indicates: device not recognized, no
"Device Description"

State: OK
Address not assigned
Address conflict
Not found

Device communicating without errors
Device address 255 (factory setting): Limited device communication
Device address already in use
Device not found

•

Devices with the following status information are highlighted in red:

−

Address not assigned

(still 255)

−

Address conflict

(e.g. duplicate address assigned)

−

Not found

•

The following devices are included in the list:

−

Synco 700 type RM…controllers (see section 1.2.1)

−

OZW771 central communication unit

−

OZW775 central communication unit

−

Synco 900 central apartment unit QAX910

−

RXB room controller

−

RXL room controller

−

QAW740 room unit

−

RMZ792 bus operator unit

−

Service tool OCI700.1

−

Area/line couplers and IP routers (depending on the setting under "Konnex
bus system" in the "Communication" dialog box, see section 5.1.2)

Edit device list

Notes

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands