Siemens OZW775 Basic Documentation Download Page 67

Page: 67 / 120

67/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Communication via zone addresses

30.08.2007

Communication via zone addresses

7.1

General notes on zones

7.1.1 Synco

zoning

Zoning in Synco is based on KNX and covers the following zones for Synco 700
devices and RXB/RXL room controllers:

Designation

RMU

RMH

RMK

RMB

RMS

RXB

RXL

Zone

address

range

Def'

value

RM...

Def.

value

RX…

Geographical zone (apartm)

x x x x x x x x 1…126 ----

----

Geographical zone (room)

x x x x x 1…63

* ----

Geographical zone (subzone)

x x 1…15

Time switch zone (apartment)

x x 1…126

Time switch zone (room)

x x 1…63

Time switch zone (subzone)

x x 1…15

Time switch slave (apartment)

x x x x 1…126 ----

Master/slave zone (apartment)

x x 1…126

Master/slave zone (room).

x x 1…63

----

Master/slave zone (subzone)

x x 1…15

QAW op.zone (apartment)

x 1…126 ----

Heat distribution zone

x x x 1…31

Heat distr zone source side

x x x x 1…31

----

Heat distr zone consumer side

x x 1…31 1

Heat distr zone heating surface

x x 1…31

----

Heat distribution zone air heater

x x 1…31

----

Heat distrib. zone, primary distr.

1…31 1

Heat distrib. zone, primary contr.

x 1…31

Refrigeration distribution zone

x x 1…31

Refrig distr zone source side

x x x 1…31

----

Refrig distr zone consumer side

x x 1…31 ----

Refrig distr zone cooling surface

x x 1…31

----

Refrig distrib. zone cooling coil

x x 1…31

----

Air distribution zone

x 1…31

Boiler sequencing zone

x 1…16

DHW zone

x 1…31

Holiday/special day zone

x x x x x 1…31

----

Time switch, DHW slave

x 1…31

Outside temperature zone

x x x x x x x 1...31

----

Solar zone

x 1...31

----

Wind zone

x 1...31

----

---- / 1 Depending on the device, the default is "----" (e.g. RMU7x0B) or "1" (e.g. RMU7x0).

See also section 7.1.4 for information on the default "----" with the series B devices.

----

With RXB/RXL room controllers "----" indicates that the zone is "out of service" and there are no
process values transmitted from this zone (in the QAX34.3 room device, "-1" is displayed
instead of "----".

The zone address range for the RXB/RXL room controllers is 0…63 or 0…15.

Zones and devices

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands