Siemens OZW775 Basic Documentation Download Page 84 | Manualshive

Page: 84 / 120

background image

84/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Large plants

30.08.2007

8.2

LTE filter table for couplers and IP routers

Area/line couplers and IP routers with an integrated LTE filter table make it possible
to filter LTE telegrams, so reducing the amount of data traffic.

The valid LTE filter table versions are version R2 and later for the Siemens
area/line coupler N140/13, and version R4 and later for Siemens IP router N146.
This means that the couplers and IP routers must be stamped R2 and R4
respectively (see section 1.4).

Note: S-mode telegrams are not subject to LTE filtering.

8.2.1 Filter

settings

The filter settings in the area/line couplers and IP routers are:

•

Normal (route)

LTE telegrams of predefined zones and zone addresses
are filtered (see the table in section 8.2.2)

•

Route all

All LTE telegrams are routed

•

Block all

All LTE telegrams are blocked

The required filtering mode is selected in ACS Service via

Applications > Popcard…

for the data point "LTE telegrams" (see screenshot).

Introduction

«
...
82
83
84
85
86
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: ATEN Pages: 176

Brand: VIS-A-VIS Pages: 4

Brand: Denver Pages: 12

Brand: Micronix Pages: 16

Brand: Polycom Pages: 4

Brand: H&B Pages: 9

Brand: On-Hold Plus Pages: 12

SceneControl 100

Brand: J.R. Clancy Pages: 13

Brand: SoundRyder Audio Pages: 20

Brand: JVC Pages: 41

Brand: JVC Pages: 10

0603MWMMDWORIJVC

Brand: JVC Pages: 26

Brand: JVC Pages: 2

Brand: JVC Pages: 2

Brand: JVC Pages: 2

Brand: JVC Pages: 2

Brand: JVC Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands