Siemens OZW775 Basic Documentation Download Page 57

Page: 57 / 120

57/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

The line address can only be set with ACS Service in programming mode.

1. Set the line coupler

locally

to programming mode. To do this, press the A5

"learning button". The red LED A4 lights up. (For a definition of "learning button
A4" and "LED A5" refer to the product and function description enclosed with
the Siemens couplers).

2. In ACS Service select

Plant > Edit device list…

to open the "Edit device list"

dialog box.

3. Only

the

Programming mode…

button is available under "Address assignment".

4. Click

Programming mode…

. The "Address assignment" dialog box opens. Enter a

line address in the range 1…15 (syntax A

.L.

0, from A

.1.

0 to A

.15.

0) and

click

Write

to confirm.

5. The new line address, 11, is adopted automatically by the line coupler when

the

Write

button is clicked.

6. Close the "Edit device list" dialog box with click on

button.

Note:

•

The red LED on the line coupler is extinguished once the line address has been

adopted.

•

The line coupler automatically adopts the area address from the superordinate

area coupler. If there is no area coupler, the area address is set to 0 (zero).

•

The Synco devices governed by the line coupler still have the "old" line address.

It is therefore essential to carry out the following steps 7, 8, 9.

Line couplers

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands