Siemens OZW775 Basic Documentation Download Page 47 | Manualshive

Page: 47 / 120

background image

47/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

1.

Set the central apartment unit

locally

to "Programming mode = On" via the

operating page "Basic setting" and the line "Programming mode" (see previous
page)

2. In ACS Service select

Plant > Edit device list…

to open the "Edit device list" dialog

box (see section 5.2.3). Click the

Programming mode…

button to open the "Address

assignment" dialog box.

3. Enter a device address in the range 1…253 (excluding 150), and confirm by

clicking the

Write

button.

When the device address (and area/line address) has been adopted the
"Commissioning" page is displayed.

Commissioning

Basic configuration…

RF connections…

Device list…

Bus communication…

Select the operating pages "Bus communication" and "Basic settings" and check
that the "Programming mode" line has automatically been reset to "Off":

Basic settings

Device address 255

Bus power supply Off

Programming mode Off

The automatic reversion to "Programming mode" = "Off" parallels the response of
the red LED switching off (e.g. the "Prog" LED on the RM… controllers).

The factory settings of the QAX910 central apartment unit can be restored. The
path for this setting is:

Main menu > Data backup > Restore factory settings > OK (acknowledge)

The configuration data is reset to the default values. The programmed device
address and the type of bus power supply remain unchanged, i.e. they are not
reset to the default values.

Procedure in programming
mode

Adopting the
device address

Note

Restoring the
factory setting

Note

«
...
45
46
47
48
49
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: Panasonic Pages: 16

Brand: HK Audio Pages: 20

Brand: Caliber Pages: 12

Brand: Fender Pages: 6

Brand: Discount Car Stereo Pages: 9

Brand: Grundig Pages: 34

RealPresence Centro

Brand: Polycom Pages: 53

Brand: EMC-PARTNER Pages: 28

Brand: Sonoro Pages: 336

SmarTouch Digital

Brand: ACC Pages: 28

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Sharp Pages: 4

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Sharp Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands