Siemens OZW775 Basic Documentation Download Page 73

Page: 73 / 120

73/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Communication via zone addresses

30.08.2007

Press the knob to confirm the zone address just set.

Geographical zone (apartment), RM… controllers

RM… default

RM… B default

----

Settings

1...126

In extensive networks it is more efficient to set zone addresses via ACS Service
than to use the RMZ790 and RMZ791 operator units (see section 5.1).

7.2.2

QAWZ740 room unit

The QAW740 room unit only contains the "Geographical zone (apartment)". The
zone address can be set by use of the operator controls on the front of the unit.

Step

Action

Operator

controls

For access to the setting mode, press the presence
button for approximately 6 seconds. A letter

displayed and the zone address can be set.

Set the zone address with the rotary knob,
In this example, the value is 5, hence

A 5

Note:

stands for "Geographical zone (

partment)"

Briefly pressing the presence button again takes the
user to other settings (for setting values with rotary
knob, see Step 2).

After setting the zone address, press the presence
button to exit from setting mode.

Zone address in the range 1…126 can be set for the "Geographical zone
(apartment)" in the QAW740 room unit.

Step 4

RM…controllers

RM…B controllers

Zone addresses
in

networks

Setting procedure

Note

Room

Geogr. zone (ap.): 5

Time switch op: Autonom

TS slave (apart.): 1

Room

Geogr. zone (ap.): 5

TS slave (apart.): ----

Time switch op: Autonom

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands