Siemens OZW775 Basic Documentation Download Page 46 | Manualshive

Page: 46 / 120

background image

46/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Device addresses via ACS

30.08.2007

The device address can be set manually via "Device address" line on the "Basic
settings" operating page. The path for this setting is:

Main menu > Commissioning > Bus communication

Commissioning

Basic configuration…

RF connections…

Device list…

Bus communication…

Basic settings

Basic setings

Device address 255

Bus power supply Off

Programming mode Off

Device address

Device address

255

100

1

Select the "Device address" line and enter a device address in the range 1…253
(excluding 150).

When the input is complete, the central apartment unit checks whether this address
is already in use. If it is not in use, the display reverts to the "Basic settings" page.
This means that the address entered is permissible and has been adopted.

If a device address is entered which is already in use, the address is not adopted.
The display does not revert to the "Basic settings" page.

The device address can be determined in programming mode via the
"Programming mode" line on the "Basic settings" operating page. For access, the
central apartment unit must be set

locally

to "Programming mode = On" via the

following path:

Main menu > Commissioning > Bus communication > Basic settings > Programming mode

Basic settings

Device address 255

Bus power supply Off

Programming mode On

Operating pages
(display)

Procedure

Note

Programming mode

«
...
44
45
46
47
48
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 36

SAPM71 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 32

Brand: Medion Pages: 308

i-Kiosk 100 Plus

Brand: FingerTec Pages: 3

Brand: Vizio Pages: 24

Brand: ITC Pages: 15

sensazone SZ/ASK

Brand: Cistermiser Pages: 16

Brand: Mantracourt Pages: 24

Brand: DriSteem Pages: 4

Brand: Multilaser Pages: 25

Brand: RCA Pages: 14

Brand: Cattron Pages: 121

Brand: Sanyo Pages: 12

Brand: Sanyo Pages: 12

Brand: Sanyo Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands