Siemens OZW775 Basic Documentation Download Page 65

Page: 65 / 120

65/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Basic communication settings

30.08.2007

6.2

Basic settings via ACS

The basic settings (see section 6.1.1 ff) can also be modified with the ACS Service
software.

After selection of the relevant device, the menu tree has the same structure as the
path sequence in the operator units, e.g. for the RMU730 controller:

Commissioning > Communication > Basic settings

1. In ACS Service

Applications > Parameter settings

, open the menu tree of the device

for which the basic settings (defaults) are to be modified.

2. Double-click the menu line "Basic settings" to open the operating page, and

select the data point for which you want to modify the default value.

3. Double-click the selected data point to open the dialog box for entering the

value.

4. Enter the value and click the

Write

button or (depending on the dialog box)

confirm the entry with the

button.

Introduction

Summary of Contents for OZW775

























































































































Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands

Siemens OZW775, Basic Documentation

Search results

Summary of Contents for OZW775

Reviews:

Related manuals for OZW775

Brands by name

Popular brands