Siemens OZW775 Basic Documentation Download Page 69 | Manualshive

Page: 69 / 120

background image

69/120

Building Technologies

Basic documentation: Communication via the KNX bus

CE1P3127en

HVAC Products

Communication via zone addresses

30.08.2007

7.1.3

Geographical zone (apartment)

The term "Geographical zone (apartment)" is specified by KNX and implies a
building divided into geographical (physical) zones. However, in practice it is
related to the operating strategy, which is defined as follows:

•

One "Geographical zone (apartment)" consists of a number of buildings or parts

of buildings which are grouped together from an operational point of view and
which obey the following criteria:

−

Same room operating mode

−

Same room temperature (setpoint, actual value).

Based on this definition, the "geographical zone (apartment)" might better be
referred to as an "operating zone".

The "geographical zone (apartment)" is used in conjunction with the RM…
controllers, the RXB/RXL room controllers and the QAW740 room unit.

Main menu > Commissioning > Communication > Room

Geographical zone (apartment)

RM… default

1

RM… B default

----

Setting

1...126

The "Room" operating page and some other operating pages for the RM…
controllers (RMU7x0 and RMH760) are different from those for the RM…B
controllers (series B devices).

Communication of the room temperature from the QAW740 to an RM… controller
via "Geogr zone 5":

QAW740

RM..

31

27

Z

3

6e

n

Room temperature

Geogr zone: 5

Room unit

Room temperature

Geogr zone: 5

Controller

Definition

Geographical zone

RM…controllers

RM…B controllers

Note

Communication of the
room temperature

Room

Geogr zone (ap.): 1

Time switch op: Autonom

TS slave (apart.): 1

Raum

Geogr zone (ap.): ----

TS slave (apart.): ----

Time switch op: Autonom

«
...
67
68
69
70
71
...
»

Summary of Contents for OZW775

























































































































Reviews:

No comments

Related manuals for OZW775

MME239 - Micro DVD Home Theater System

Brand: Magnavox Pages: 41

Brand: Yealink Pages: 6

MeetingSpace VC800

Brand: Yealink Pages: 6

Brand: Yealink Pages: 16

Brand: Yealink Pages: 4

Brand: Yealink Pages: 20

Brand: Yealink Pages: 299

VC210 Teams Edition

Brand: Yealink Pages: 12

Brand: Yealink Pages: 5

Brand: Yealink Pages: 16

Brand: Yealink Pages: 30

MeetingSpace VC200

Brand: Yealink Pages: 8

MVC Series: MVC800

Brand: Yealink Pages: 16

CP930W Telesystem

Brand: Yealink Pages: 2

Brand: Yealink Pages: 16

Brand: Zonex Pages: 28

POLYCOM VTXTM 1000

Brand: Polycom Pages: 2

Brand: Aiwa Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands