28
V115E_09.20
T r o u b l e s h o o t i n g
Series-65H Hoist Pos 4
KW Aufzugstechnik GmbH OPERATING MANUAL DAVID-613
DAVID-D613-V106-E 21.12.2016 Page - 178 -
F133
Monitor Brake-4:
-
Brake-circuit-4 do not open / close during the travel -> Are the settings OK? Do you have
opener or closer-contacts? 0V (NPN-Thyssen ) or+24V (z.B. Ziehl-Abegg,..)
-
Do have connected the brakewires rightly?
-
Do you have observed, if the brakes open ? -> Brakewires ?
- Are the brake-contacts
OK ? -> If you have any douts, make a measurement !
F134
Monitor Main Contactor:
-
One of the main contactor can not be switched ON -> Please control the contactors!
-
Please check the opener-contacts, clean it or change it!
- Are the opener-contacts for 24V DC ? -> Please look at the data sheet!
F135
ADC1-Zero-Offset:
- The currentsensor-U is out of order. It is an internal Error. Please contact our Hotline.
F136
ADC2-Zero-Offset:
- The currentsensor-V is out of order. It is an internal Error. Please contact our Hotline.
F137
ADC1-Offset:
- The AD-Changer-
V
is out of order. It is an internal Error. Please contact our Hotline.
F138
ADC2-Offset
:
- The AD-Changer-
U
is out of order. It is an internal Error. Please contact our Hotline.
F139
Eart Fault:
- The motor ist out of order, please measure each coil of the motor and compare it!
- Please check, if the motorwire or resistorwire have any connection to earth!
F140
IPM-Error: or Supply voltage to low:
-
Overtemperature in the IGBT-Chip -> Are there any dirt on the pcb-board or in the heatsink ?
- The voltage of board is too low! -> Is the main supply voltage OK ?
F141
Position Regulation:
-
The difference at the start handling is too high, wrong Parameter (
Nominalspeed
-> motor-
datas,..)!
-
The motor works, but the encoder is out of order or wrong connected. -> Control the pining!
-
Perhaps it is the wrong type of encoder? ->
Menu A4 Motor/Gearbox -> Encodersystem
-
The number of pulses are wrong? ->
Menu A4 Motor/Gearbox -> Encoder Pulses
-
The encoderwire is out of order or too long ( >30m) ! -> Please increase the encoder voltage !
-
The encoderwire is parallel to the motorwire -> Change it immedately!
-
The encoder-shield is not connected on both sides -> Change it immedately!
Old machines: Please switch off the
possition regulator
! Or change the settings!
F142
NTC-Dissipator ::
- The Temperature sensor deliever the wrong value: Please check the connection!
- The Temperature sensor is out of order. Please contact our Hotline.
F143
DC Battery Voltage:
At the evaquation-travel with battery, the voltage of the battery was too low. Please check the battery
voltage!
F144
Watchdog-Reset
There is an internal Reset by the Watchdog. Please contact our Hotline.
F145
Monitor Brake wear-1:
The input channel for the Brake wear monitor is active.You need a new brake
shoe or brake is not exactly adjust!
F146
Monitor Brake wear-2:
The input channel for the Brake wear monitor is active.You need a new brake
shoe or brake is not exactly adjust!
F147
Monitor Brake wear-3:
The input channel for the Brake wear monitor is active.You need a new brake
shoe or brake is not exactly adjust!
F148
Monitor Brake wear-4:
The input channel for the Brake wear monitor is active.You need a new brake
shoe or brake is not exactly adjust!
F149
Offset measure Pole Number:
There is a difference between the parameter motor type and the actual type!
F150
Offset measur Brake:
During the offset measure, the motor do not rotate – please check the brake, because it is not open!
F151
Offset measure Invalid :
The measured offset angle is not valid – check electric wiring and make the offset measure a second
time!
F152
Brake Resistor:
There is a short cut at the brake resistor!
Summary of Contents for 65H Series
