Samwon Tech Temp 2000 M Instruction Manual Download Page 80

Page: 80 / 181

SAMWONTECH

2nd Edition of TEMP2000M_Series IM : April. 8. 2014 Page 76 / 176

6.4 SD memory storage setting

▶

It is a set the necessary item in data backup on SD card.

☞

It is a screen to display only in SD card option.

①

It sets the transmitting item and transmitting direction in SD CARD and TEMP2000M.

☞

Download : It means the transmitting the selected items out of the TEMP2000M internal data to SD
card.

☞

Upload : It means the transmitting the selected items out of the saved data in SD card to TEMP2000M.

☞

Ptn : The pattern set in [5.1 Program pattern setting] can be downloaded or uploaded.

☞

Para : The set parameter can be downloaded or uploaded.

☞

All : The pattern and parameter can be downloaded or uploaded.

②

It displays current SD CARD capacity.

☞

It is displayed when SD CARD is inserted.

③

The

(Transmitting) button is activated when the program and stationary operation are stopped and

download or upload is available when

(Transmitting) button is pressed.

Table 6-3. Graph & Save the 5

screen parameter

Parameter

Setting range

Unit

Initial data

Transmission item

PTN, Para, All

ABS

Pattern

Transmission

direction

Downloadl, upload

ABS

Download

[Fig 6-11] Graph & Save setting the 5

screen

①

②

③

Summary of Contents for Temp 2000 M






















































































































































































Search results

Summary of Contents for Temp 2000 M

Reviews:

Related manuals for Temp 2000 M

Brands by name

Popular brands

Samwon Tech Temp 2000 M, Instruction Manual

Search results

Summary of Contents for Temp 2000 M

Reviews:

Related manuals for Temp 2000 M

Brands by name

Popular brands