Samsung DVM Series Service Manual Download Page 67

Page: 67 / 390

4. The outdoor unit starts a tracking to check the connected indoor unit and option at power ON.

●

The left of outdoor unit PCB check display part checks the

responded indoor unit by communication to 0~F address,

and displays the responded address to the right of PCB

check display part.

●

Check if the indoor unit address at installation and the indoor

unit address responded is same.

●

Check if the number of indoor unit installed and the number

of outdoor unit PCB setup is same.

●

If the number of indoor unit set on outdoor unit PCB and

responded by communication is same after tracking, go

ahead the next step.

●

If CH is displayed on the part of outdoor unit PCB check

display after completion of tracking, the compressor is not

preheated. Turn the power On to heat the compressor, and

wait until the CH is disappeared.

●

The communication between the indoor unit and the outdoor unit is performed if the compressor is preheated. And the

connected indoor unit address is displayed at the right of the outdoor unit PCB check display part.

5. Check the system pressure by use of manifold gauge.

●

Connect the manifold gauge with the high/low pressure

service valve of outdoor unit.

●

Check if the high/low pressure service valves are all opened.

●

Operate the system by pressing the refrigerant charge key.

●

Check the high/low pressure through the manifold gauge.

●

Refer to the pressure table classified by the outdoor

temperature and the length of drain pipe provided separately

for a proper pressure.

●

Stop the system by pressing the refrigerant charge key.

Check if the indoor unit address is responded as a same.

- 66 -

Installation

Left Right

PCB display part

High pressure side

Mani hold gauge

Low pressure

side

• E2 is displayed on the part of outdoor unit PCB check display if the tracking is failed.

• Perform the re-tracking by pressing KEY 3 after checking address of indoor and outdoor unit.

• Check the input value after 30 minutes after running the compressor because the high/low is changed

continually at the initial operation.

• Don't perform the system operation more than 1 hour to check system pressure.

DB98-17816A(1)_1~4 3/2/04 9:31 AM Page 66

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands