Samsung DVM Series Service Manual Download Page 189

Page: 189 / 390

- 188 -

Troubleshooting

8-2-22. Communication error in tracking

Check by comparing of set values of installed

numbers of indoor units on outdoor unit

PCB with actual installed numbers.

Press reset key (K3) on the outdoor unit

PCB to check the display part and then

check the indoor unit numbers with

response to the tracking.

Remove the communication cable from

outdoor unit to indoor unit and measure

two lines of outdoor unit side with scope?

Is there no response of indoor unit

on display part during tracking?

Reconnect the communication line from

outdoor unit to indoor unit and check the
communication line changing (it must be

not change F1 and F2) and then reconnect

one by one to locate the indoor unit

obstructing the communication,

and then replace the PCB.

The voltage between

two lines is wave of DC±0.7V as

shown in the following:

Is the numbers of indoor

units installed same as those of set values on

the setting switch?

Set the installed numbers of indoor

units on outdoor unit correctly and then press

reset key (K3) on the outdoor

unit PCB to track indoor units again.

Locate the indoor unit having the

communication error after 2 minute and check

the duplication of PCB address.

(If the address of indoor unit is

duplicated, communication error occurs.)

- In such a case the communication error

appears from more than 2 sets

of indoor units whose addresses

are wrong.

If there is no trouble in the address, replace the

PCB after checking the communication cable.

Check the outdoor unit communication

cable of PCB and replace the PCB.

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- Mismatching of the indoor unit numbers set with those communicated during

outdoor unit tracking.

- Communication error between indoor unit and outdoor unit, and switch setting

error for installed numbers.

Yes

DB98-17816A(1)_8 3/2/04 9:35 AM Page 188

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands