Samsung DVM Series Service Manual Download Page 154

Page: 154 / 390

- 153 -

Refrigerating Cycle Diagram

6-2-7. Main parts status

1. Digital scroll compressor

The variable capacity type compressor to control the capacity up to 10 ~ 100% with 19 steps

2. Accumulator

To prevent the incoming of the liquid refrigerant to the compressor (prevention of liquid back).

3. Receiver

To reduce the noise by flowing the high pressure liquid refrigerant to the high pressure pipe and to control

the amount of refrigerant during the individual operation of indoor unit.

4. Solenoid valve (PWM)

It is installed at the top of digital scroll compressor and at the low pressure pipe, which is used for operating the digital scroll

compressor. When the valve is open, the digital scroll compressor keeps the state of

unloading.

5. Solenoid valve (HGBV)

When the low pressure gets lower, the valve is open by the low pressure safety device. The valve is open in order to reduce

the load at the start of compressor and when the system stops and then keep the balance of low pressure.

6. Solenoid valve (LBV)

When the compressor is overheated, it actuates to lower the temperature of compressor for stable operation.

7. Solenoid valve (VBV)

The valve is open in order to reduce the load at the start of compressor and when the system stops and then keeps the

balance of low pressure.

8. High pressure switch (HPS)

To stop the system for the system protection when the high pressure exceeds the set value.

9. Temperature sensor (DTS, Discharge Temperature Sensor)

It is the means to measure the refrigerant temperature of compressor outlet which is used as the data

for control of compressor.

10. Temperature sensor (COS, Condenser Out Sensor)

10.

When heating, used for defrost control by sensing outdoor heat exchanger temperature.

11. Temperature sensor (OATS, Outdoor Air Temperature Sensor)

10.

To measure the outdoor temperature which is used for the determination of start method.

12. Fixed scroll compressor

10.

The fixed capacity type compressor.

DB98-17816A(1)_6~7 3/2/04 9:33 AM Page 153

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands