Samsung DVM Series Service Manual Download Page 236

Page: 236 / 390

- 235 -

Troubleshooting

8-2-67. Prohibit to start compressor according to the outdoor temperature

■

Check method

■

The above error code is not the products error, but specification to protect the products by restricting the use

temperature ranges. Use it by reference to the temperature range of use condition in manual.

If the above error code is occurred despite of condition being not included above judge method, read the value

of outdoor inlet air temperature by use of view mode or S-net. And then if it is different with the actual outdoor

temperature, replace the temperature sensor.

Indoor unit display

Outdoor unit display

Judgment method

Causes

(30˚C over of outdoor temperature on heating mode)

(-5˚C below of outdoor temperature on cooling mode)

- If the outdoor temperature is below -5˚C at the right before of compressor start,

prohibit cooling operation.

- If the outdoor temperature is over 30˚C at the right before of compressor start,

prohibit heating operation

- Operation prohibit mode according to the limit of outdoor temperature

➞

DB98-17816A(1)_8 3/2/04 9:35 AM Page 235

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands