Samsung DVM Series Service Manual Download Page 114

Page: 114 / 390

- 113 -

Wall-mounted type

(cont.)

Parts

Procedure

Remark

Ass'y

Tray Drain

Electrical Parts

(Main PCB)

Heat Exchanger

1) Separate the drain hose from the extension

Tray Drain.

2) Take the display PCB out.

(Right of indoor unit)

3) Pull Tray Drain out from the Back Body.

1) Take all the connector of PCB upper side

out. (Inclusion Earth Wire)

2) Separate the outdoor unit connection wire

from the terminal block.

3) If pulling the Main PCB up. It will be taken

out.

1) Loosen the fixing earth screws of right side.
2) Separate the connection pipe.
3) Separate the bush body at the upper side

and holder at the rear side.

4) Loosen the fixing screws of left side.
5) Lifting the Heat Exchanger up a little to push

the up side for separation from the Indoor
Unit.

Disassembly and Reassembly

DB98-17816A(1)_5 3/2/04 9:32 AM Page 113

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands