Samsung DVM Series Service Manual Download Page 199

Page: 199 / 390

- 198 -

Troubleshooting

Is the resistance

normal between compressor

terminals?

Is high pressure and

low pressure normal?

Is the compressor operating?

Even though the compressor is operating

but if there is no response on the

temperature, it is the loading failure.

Replace the PWM valve.

If any one of the resistance of compressor

terminals L1(R)-L2(S), L2(S)-L3(T) and L3(T)-L1(R) is not

normal, it shall be regarded as OLP

trip and then wait until the compressor is

cooled to restart.

If the compressor is under normal operation,

check the causes of OLP trip (amount of

refrigerant, outdoor ventilation structure, etc).

Even though On signal is going to compressor

but if it is not operating, it is the OLP trip due

to the overload, wait to start until the

compressor is cooled.

Error reset (key3)

Test operation (key 4)

- All indoor units

2. Caution

1) The replacement of PWM valve due to the loading failure is the difficult work to abolish the refrigerant in the

system and recharge it, and there is little possibility to appear actually.

So check the above check items carefully.

2) The restart is possible only when the inside temperature of compressor is down lower than

60°C, and therefore it takes about 2-3 hours.

3) If waiting at the state that the power is on during the temperature falling down.

CCH (crank case heater) operates to delay the time to restart. Accordingly, separate the connector to the

CCH (crank case heater) to block the power and reconnect the connector after the completion of final check.

Yes

DB98-17816A(1)_8 3/2/04 9:35 AM Page 198

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands