Samsung DVM Series Service Manual Download Page 230

Page: 230 / 390

- 229 -

Troubleshooting

8-2-61. Indoor unit freezing protection

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- When the temperature of indoor unit heat exchanger on cooling operation maintains

over 5 minutes below -4˚C

- Indoor fan motor defect or lock

- EEV open error

Yes

Check the indoor unit detected

freezing.

Error reset(KEY3)

It is completed to check the system.

Test operation for every

room(KEY 4)

Operate a corresponding

indoor unit.

Remove the obstacles of

corresponding indoor unit and clean

the dust filter.

Does operate normally the

indoor unit fan motor?

Is the voltage of PCB fan

motor output terminal normal?

Replace the motor after checking

the connection wire of fan motor.

After checking the quantity of

refrigerant, if needed recharge

the refrigerant.

Restart after PCB

exchange.

Is high/low pressure normal ?

✳

If the outdoor temperature is so low(below -5˚C) or a number of indoor unit is off simultaneously, the indoor unit can be frozen in an instant.

DB98-17816A(1)_8 3/2/04 9:35 AM Page 229

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands