Samsung DVM Series Service Manual Download Page 217

Page: 217 / 390

- 216 -

Troubleshooting

8-2-47. Communication error between the indoor unit and outdoor unit on tracking

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- When the number of indoor unit of installation switch mismatch with communicated indoor unit on

tracking the outdoor unit

- Communication error between the indoor unit and outdoor unit, and the setting switch setup error for

the installation number of indoor unit

Compare and check the setting switch setup

value for indoor unit installation number of

outdoor unit PCB with the actual indoor unit

installation number.

Press the reset key(K3) of the outdoor unit PCB
and check the number of indoor unit responding

to the tracking at display part.

Remove the communication wire connecting

from the outdoor unit to the indoor unit, and then

measure 2 wires of the outdoor unit with scope.

Is there any response of indoor unit at display

part on tracking?

Check the communication wire connecting

from the outdoor unit to the indoor unit.

If there is no defect, search the indoor unit that

interrupts the communication by connecting the

indoor unit one by one. And after check a wire,

displace the indoor unit PCB.

Is the voltage between both wires square

wave over DC 0.7V?

Is same the actual indoor unit

installation number and the setting

switch setup value for indoor unit

installation number?

After right setting the setting switch setup

value for indoor unit installation number of

outdoor unit, perform the tracking again by

pressing the reset key(K3) of PCB.

Search for the indoor unit displayed the

communication error after 2 minutes, and check

the duplication of PCB address setup.

(The communication error is occurred

due to address duplication.)

In this case, the communication error is

occurred at the every indoor unit (over

2ea) set wrong address.

If there is no defect in address,

replace the indoor unit PCB after check the

communication wire.

After check the communication wire

and connecter of the outdoor unit PCB,

replace the PCB.

Yes

DB98-17816A(1)_8 3/2/04 9:35 AM Page 216

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands