Samsung DVM Series Service Manual Download Page 63

Page: 63 / 390

4-3. The setting of indoor Address

4-3-1. Specification 1

●

The indoor unit of system air conditioner must be set address.

●

Set the address as follows by use of the address setup switch of indoor unit PCB.

- 62 -

Installation

K1 K2 K3 K4

K5 K6 K7 K8

K9 K10 K11 K12

SW03

SW04

SW05

SW01 RMC

SW02 MAIN

SW01 RMC

●

SW02 main switch is a basic address for the communication between indoor unit and outdoor unit.

The products operate normally when this address is set.

●

Address setup is available from 0 to F. Set from 0 to the last installation number to another address.

Indoor units connected with the same outdoor unit should have another address.

●

Before the installation of indoor unit, mark the address of indoor unit onto the drawing for address setup.

●

SW01RMC switch is an address setup switch to control the indoor unit operation by the wired remote control

and centralized controller.

●

If the wired remote control and centralized controller is used, SW03 K1, K2 switch setup should be needed.

●

SW01 RMC switch setup is not needed for the outdoor unit which dose not use the wired remote control and

centralized controller.

• PCB type may be different according to the model.

ote

DB98-17816A(1)_1~4 3/2/04 9:31 AM Page 62

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands