Samsung DVM Series Service Manual Download Page 175

Page: 175 / 390

- 174 -

Troubleshooting

Error reset (KEY 3)

Test operation (KEY4)

Is both service valves open?

Since the service valve is clogged, open

the service valve.

Since it is the electronic expansion valve

close error, check the electronic expansion

valve and PCB related.

Since it is the defect of compressor

unloading, check the coil end of PWM

valve. If there is no trouble in the coil,

replace the PWM valve.

Is the low pressure

rapidly dropping and the

discharge temperature

increasing?

Since the refrigerant is insufficient,

check to charge if needed.

Are all indoor units

operated normally?

Is high pressure and low

pressure normal?

Are all the above check

items normal?

Complete the test operation mode

and check for 1 unit operation

The system check is

completed.

Operating

pressure

(kg/cm

OPEN

1.2±0.2

2.2±0.2

Low switch specification

8-2-4. Low pressure switch detection

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- Operation stop when low pressure is lower than 1.2kg/cm

G(sensor open)

System down if the two times of the same situation occurs after restarting

(Counter cleared if no defection for 1 hour)

- Low temperature start(outdoor temperature is lower than -5°C

- Leakage / Shortage of refrigerant

- Compressor unloading failure

- Service valve clogged/electronic expansion valve clogged

✳

The minimum applicable temperature of DVM is -5°C and the system may not operate normally below the temperature by the low pressure switch.

Yes

DB98-17816A(1)_8 3/2/04 9:34 AM Page 174

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands