Samsung DVM Series Service Manual Download Page 177

Page: 177 / 390

- 176 -

Troubleshooting

Check the indoor unit whose

freezing is detected.

Error reset (KEY 3)

System check is completed.

Test operation of all

units (KEY 4)

Operate one unit of

related indoor unit.

Remove the obstacles around air inlet

of indoor unit and

clean the air filter.

Is indoor unit fan motor

operation normal ?

Is PCB fan

motor outgoing terminal

voltage normal ?

Check the fan motor

connection cable and

replace the motor

Check the refrigerant

and charge if necessary.

Replace the PCB

and reoperate.

Is high and low pressure

normal?

✳

The indoor unit may be frozen instantaneously if outdoor temperature is too low (lower than -5°C) or many indoor units are off at the same time.

8-2-6. Freezing of heat exchanger

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- When the indoor unit heat exchanger temperature is kept at -4°C for

more than 40 seconds

- Indoor fan motor stocked or bad

Electronic expansion valve open error

Yes

DB98-17816A(1)_8 3/2/04 9:34 AM Page 176

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands