Samsung DVM Series Service Manual Download Page 172

Page: 172 / 390

Yes

8-2-1. High temperature of discharge sensor

- 171 -

Troubleshooting

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- Restart after operation stops when the discharge temperature exceeding 135°C is detected

- System down when two times of detection is made

(count is cleared when no detection is made for one hour)

- Shortage of refrigerant

- Compressor unloading defective (unloading failure)

- Service valve clogged

- Electronic expansion valve clogged

Error reset (Key 3)

Is both service valves open?

Since the service valve is clogged, open

the service valve.

Since it is the electronic expansion valve

close error, check the electronic expansion

valve and PCB related.

Since the refrigerant is insufficient,

check to charge if needed.

Is the low pressure

rapidly dropping and the

discharge temperature

increasing?

Since it is the defect of compressor

unloading, check the coil end of PWM

valve. If there is no trouble in the coil,

replace the PWM valve.

Test operation (key 4)

The system check is completed.

Are all indoor units

operated normally?

Is high pressure and

low pressure normal?

Is all the above check

items normal?

Complete the test operation mode

and check for 1

unit operation

Yes

DB98-17816A(1)_8 3/2/04 9:34 AM Page 171

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands