Samsung DVM Series Service Manual Download Page 168

Page: 168 / 390

8-1-2. Reverse phase/missing phase detection - P4 indicated if abnormal

1. To check the power to be used for 3 phase power compressor if the power is on.

If there is any change of order for 3 phase L1(R)-L2(S )-L3(T) (reverse phase) or the power is not on,

Er and P4 are indicated alternately and the air conditioner is kept to stop.

1) L1(R)-L2(S) phase/L1(R)-L3(T) phase/L2(S)-L3(T)phase are checked.

2) If there is any terminal not having the normal voltage, check the external power of air conditioner for action.

3) If the 3 phase power is normal, it is the phase power is changed. Change two wires of incoming of power from

external side or incoming part of air conditioner.

For example, change L1(R) with L2(S).

4) Press reset key (K3) after above check and check the power again.

5) If there is abnormal condition even after one more check, check the color of 3 phase power.

If there is no abnormal as a result of check, replace the PCB.

- 167 -

Troubleshooting

Display

Reset key

wire for 3 phase
power check

indoor power

supply line

single phase
AC220V supply
line

3 phase power

supply line

communication line

clamp

DB98-17816A(1)_8 3/2/04 9:34 AM Page 167

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands