Samsung DVM Series Service Manual Download Page 218

Page: 218 / 390

- 217 -

Troubleshooting

+0.7V

-0.7V

Check the display part with pressing the rest

key(K3) of the outdoor unit PCB.

Is the voltage between both wires square

wave over DC 0.7V?

Is there any response of the indoor unit

at the display on tracking?

Remove the communication wire

connecting from the outdoor unit to the

indoor unit, and then measure 2 wires of

the outdoor unit with scope.

Check the communication wire connecting from the

outdoor unit to the indoor unit. If there is no defect,

search the indoor unit that interrupts the communication

by connecting the indoor unit one by one. And after

check a wire, displace the indoor unit PCB.

Search for the indoor unit displayed the

communication error after 2 minutes, and check

the duplication of PCB address setup.

(The communication error is occurred due to

address duplication.)

In this case, the communication error is occurred at
the every indoor unit (over 2ea) set wrong address.

After check the communication wire

and connecter of the outdoor unit PCB,

replace the PCB.

GOOD

BAD

If there is no defect in address, replace the indoor unit

PCB after check the communication wire.

8-2-48. Communication error after the completion of tracking

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- When it is not communicated between the indoor unit and outdoor unit during the operation

- Communication error between the indoor unit and outdoor unit

Yes

DB98-17816A(1)_8 3/2/04 9:35 AM Page 217

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands