Samsung DVM Series Service Manual Download Page 231

Page: 231 / 390

- 230 -

Troubleshooting

8-2-62. High pressure protection control

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- It is detected when the value of high pressure sensor is over 28kg/cm

<Cooling operation>

- Outdoor unit fan motor error(lock, defect)/Fan motor capacitor defect or wire short

Outdoor heat exchanger pollution/SSR defect for fan control/Service valve lock

<Heating operation>

- Outdoor unit fan motor error(lock, defect)/Capacitor defect or wire short

PWM valve defect of digital compressor /Service valve lock

Error reset(KEY 3)

Check completion

Check the PWM valve coil

and connecter.

Is high/low pressure normal?

Is the service vale opened all?

Open the service valve.

S-net connection (Essential)

Check the quantity of refrigerant

Operate the indoor/outdoor EV

Check the EEV clogging

Check the Coil attaching and the

connection of connecter.

Cooling

Heating

Test operation

(The same condition with that

error occurred)

Remove the pollutions and

obstacles of outdoor inlet

and discharge.

Remove the pollutions and

obstacles of indoor inlet and

discharge.

Check if the outdoor fan is

operated normally.

Check if the indoor fan is

operated normally.

Yes

DB98-17816A(1)_8 3/2/04 9:35 AM Page 230

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands