Samsung DVM Series Service Manual Download Page 238

Page: 238 / 390

- 237 -

Troubleshooting

■

Check method

■

This is not the error, so normal heating operation is performed after defrost.

8-2-69. Defrost operation

Outdoor unit display

Indoor unit display

Judgment method

Causes

- The operation to defrost in the outdoor heat exchanger during the heating operation

- Defrost operation (Not error)

■

Check method

■

If the capacity of indoor unit is low at the below 0˚C of outdoor temperature in cooling, this is specification to control

compressor ON/OFF. It is not an error and possible to operate normally.

8-2-70. Low discharge pressure control

Outdoor unit display

Indoor unit display

Judgment method

Causes

- The operation is continued with the high pressure of 9kg/cm

for 10 minutes.

- When the capacity of indoor unit for cooling is below 4000W in the condition of

low outdoor temperature(below 0˚C)

■

Check method

■

This is a special operation mode to obtain oil level between the compressors on the system used many compressors,

and is not error. After oil leveling operation for 4~6 minutes, it returns to the normal operation automatically.

8-2-71. Oil leveling

Outdoor unit display

Indoor unit display

Judgment method

Causes

- Operation to exchange the oil between the compressors (Oil leveling operation)

- Oil leveling operation

DB98-17816A(1)_8 3/2/04 9:35 AM Page 237

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands