Samsung DVM Series Service Manual Download Page 188

Page: 188 / 390

- 187 -

Troubleshooting

+0.7V

-0.7V

Press the reset key (K3) of outdoor unit

PCB and check the display.

The voltage between

two lines is wave of DC±0.7V as

shown in the following:

Is there no response of

indoor unit on the display

during tracking?

Remove the communication cable

from outdoor unit to indoor unit and

measure 2 lines of outdoor unit side with

scope.

Re-connect the communication line from

outdoor unit to indoor unit and remove all

communication connector from indoor unit PCB,

and then re-connect one by one to locate the indoor

unit obstructing the communication,

and then replace the PCB.

Locate the indoor unit having the

communication error after 2 minutes and check the

duplication of PCB address.

(If the address of indoor unit is duplicated,

communication error occurs)

-In such a case the communication error appears

from more than 2 sets of indoor units whose

addresses are wrong.

Check the outdoor communication

cable of PCB and connector and then

replace the PCB.

good

bad

If there is no trouble in the address, replace the PCB

after checking the communication cable.

Yes

8-2-21. Communication error after completion of tracking

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- In case that the communication is not available for 2 minutes during operation

between indoor and outdoor unit.

- Communication error between indoor unit and outdoor unit

DB98-17816A(1)_8 3/2/04 9:35 AM Page 187

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands