Samsung DVM Series Service Manual Download Page 196

Page: 196 / 390

- 195 -

Troubleshooting

1. Judgment method

1) In cooling mode (The following conditions shall be satisfied for more than 20 minutes)

2) In heating mode (All following conditions should be satisfied)

(1) More than 2 indoor units are operating in THEMO ON heating mode.

(2) Average of high pressure is more than 18kg/cm

(3) 5 minutes after completion of the safety start.

(4) The condition of ‘indoor unit T(EVAP_in) < T(room)+3°C and T(EVAP_out) < T(room)+3°C’ is maintained for 5 minutes.

2. Check method

1) Check whether the electronic expansion valve wire is connected correctly to the indoor unit PCB.

2) Open the electronic expansion valve kit to check whether the electronic expansion valve coil is correctly inserted.

3) Press the reset key (K3) of outdoor unit to check whether the same error appears.

- If it is the close error, operate the related indoor unit.

- If it is open error, put the related power off to check.

4) If there is no trouble for the above check items, replace the electronic expansion valve.

- Since the replacement of electronic expansion valve is the inconvenient work to recover the all refrigerant in the system,

be sure to check the above items before replacing it.

8-2-28. Electronic expansion valve close error

Outdoor unit display

Indoor unit display

Judgment method

Causes

(Close error of xth electronic expansion valve)

(Operation)

(Timer)

(Fan)

(Filter)

(Removing frost)

- Refer to the following judgment method

- Indoor unit electronic expansion valve close error

Tcond, mid-Tair, out > 3°C

Tcond, out - Tair, out > 3°C

Tair, in - Teva, in > 4°C

Tair, in - Teva, out > 4°C

Compressor operating &

indoor unit operating and thermo on

Error contents

Electronic expansion valve close error

DB98-17816A(1)_8 3/2/04 9:35 AM Page 195

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands