Samsung DVM Series Service Manual Download Page 240

Page: 240 / 390

- 239 -

Troubleshooting

Is the resistance value

between the compressor

terminals normal?

Is high/low pressure normal?

Is the compressor operating?

Even though the compressor is operating

but if there is no response on the

temperature and pressure, it is the loading

failure. Replace the PWM valve.

If any one of the resistance value of compressor

terminals L1(R)-L2(S), L2(S)-L3(T), L3(T)-L1(R) is

not normal, it shall be regarded as OLP Trip. Wait

until the compressor is cooled to restart.

If the compressor is under normal operation,

check the causes of OLP trip(amount of

refrigerant, outdoor ventilation, etc).

Even though ON signal is going to

compressor but if it is not operated, it is the

OLP trip due to the overload. Wait until the

compressor is cooled to restart.

Error reset(KEY 3)

Test operation for every room

(KEY 4)

■

Precautions

■

1. The replacement of PWM valve due to the loading failure is the difficult work to abolish the refrigerant in the system and

recharging it, and there is little possibility to appear actually.

So, check the above check items carefully.

■

2. The restart after OLP trip is possible only when the inside temperature of compressor is down lower than 60˚C, and

therefore it takes about 2-3 hours.

■

3. If waiting at the state that the power is on during the temperature failing down.

CCH(Crank case heater) operates to delay the time to restart. Accordingly, separate the connecter to the CCH to block

the power and reconnect the connecter after the completion of final check.

Yes

DB98-17816A(1)_8 3/2/04 9:35 AM Page 239

Summary of Contents for DVM Series







































































































































































































































































































































































































Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands

Samsung DVM Series, Service Manual

Search results

Summary of Contents for DVM Series

Reviews:

Related manuals for DVM Series

Brands by name

Popular brands