manualshive.com logo in svg

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 96 / 156

Share
Download
Rural King RK19 Hydrostatic Operator'S Manual Download Page 96

5 - 1

Maintenance and service

435

greasing pOints

For general greasing points, refer 

to the fuel, oil and fluid specification 

chart. (See page 5-.)
However, add grease before work 

if the tractor is to be used in a wet 

field.

greasing brake arM  

Remove  the  rubber  caps  on  the 

floor and dash panel to access to 

the grease nipple.
Add grease with the supplied grease 

gun.

►

►

8. greasing

9. checking hOses

Rubber parts, such as the fuel hose 

and radiator hose, are aged by time 

even when the tractor is not in use. 

Therefore,  such  parts  should  be 

replaced with their tightening bands 

every    years  or  when  they  are 

damaged.

If  any  fuel  hose  is  damaged, 

fuel leaks and it can catch fire. 

Make  sure  to  check  the  fuel 

hose and take a necessary ac-

tion.

•

Warning

RK19-영문-05(마).indd   13

2017-05-18   오후 6:35:24

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments