Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 93 / 156

5 - 10

Maintenance and service

④

Run the engine for approx. 5

minutes and check for proper

operation through the engine oil

warning lamp. Then, stop the

engine.

(This warning lamp should be

turned off while the engine is

running.)

⑤

Check the oil level with the dip-

stick again. If still insufficient,

add more.

replacing engine Oil

filter cartridge

①

Remove the engine oil filter car

tridge by turning it counterclock-

wise with a filter wrench.

②

Apply a thin film of oil to the

O-ring of a new cartridge and

install the new cartridge by

tightening it with a hand. When

its packing touches the sealing

surface, turn it approx. 2/3 turns

further with a wrench.

③

Add engine oil to the specified

level.

►

T9O51A

pliers

Engine oil

gauge

Engine oil

Filter Cartridge

T19O511A

RK19-영문-05(마).indd 10

2017-05-18 오후 6:35:22

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands