Rural King RK19 Hydrostatic Operator'S Manual Download Page 56

Page: 56 / 156

2 - 1

DESCRIPTION OF TRACTOR CONTROLS

THROTTLE LEVER

It is used to adjust the engine speed
like the throttle pedal.

Pushing : increasing speed

Pulling : decreasing speed

►

Throttle lever

bRAKE PEDEL

The brake pedal is located on the

LHS of the operator.
It is used for two functions.
- To stop the tractor
- To release cruise control

►

Brake pedal

Never use it unless working in

a field. It can lead to speeding

and an accident.

•

WARNING

T19O119A

DRIVING SPEED CONTROL

PEDAL

When depressing the forward driv-

ing speed control pedal, forward

driving is selected. Reverse driving

is selected by depressing the re-

verse driving speed control pedal.

When releasing the speed control

pedal, it is returned to the neutral

position and the tractor is stopped.

►

Driving speed

control pedal (forward)

Driving speed

control pedal (backward)

T19O120A

T19O121A

RK19-영문-02(나).indd 13

2017-05-18 오후 6:22:46

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 56 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: