manualshive.com logo in svg

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 71 / 156

Share
Download
Rural King RK19 Hydrostatic Operator'S Manual Download Page 71

3 -

OPERATION

hOw TO sTART ENgINE

①

  Make  sure  that  there  is  no  ob-

stacle around the tractor.

②

  Seat  on  the  driver's  seat  and 

confirm that the parking brake is 

applied.

③

  Check  that  each  shift  lever  and 

PTO  switch  are  in  the  neutral 

position.

④

 Pull the throttle lever halfway.

⑤

 

Insert  the  key  into  the  main 

switch  and  turn  the  switch  to 

the  "ON"  position.  Check  that 

the  engine  oil  lamp  and  charge 

warning lamp come on.

⑥

 

Turn  the  main  switch  to  the 

"START"  position.  When  the 

engine  is  started,  release  the 

switch.

⑦

 Confirm that all monitoring lamps 

go off after the engine is started.

►

1. ENgINE sTARTINg

The engine will not start unless 

the brake pedal is depressed.
Do not turn the main switch to 

the "START" position while the 

engine is running.
Avoid running the start motor 

over 10 seconds. It consumes a 

lot of current.

If the engine cannot be started 

within 10 seconds, wait for 30 

seconds and try it again.
The engine cannot be started 

unless the driver is seated on 

the driver's seat. Start the en-

gine on the driver's seat.

•

•

•

•

•

NOTE

Never start the engine by con

-

necting the start motor terminal 

or  safety  switch  directly. The 

tractor may move suddenly and 

cause an accident.

•

wARNINg

RK19-영문-03(다).indd   2

2017-05-19   오전 9:45:13

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments