Rural King RK19 Hydrostatic Operator'S Manual Download Page 118

Page: 118 / 156

7 - 7

TROUBLESHOOTING

437

4. HYdRaULIc SYSTEM

TROUBLE

PROBaBLE caUSE

SOLUTION

Hydraulic system

Oil leaks from the pipe

or hose

Loose clamp

•

Tighten

•

Cracked pipe

•

Have it replaced by workshop

•

The hydraulic pressure

won't be decreased

Lowering speed control lever fixed to stop position

•

Set it to the lowering position

•

Defective valve

•

Have it repaired by workshop

•

Damaged cylinder

•

Have it repaired by workshop

•

Damaged and seizured lift shaft rotating part

•

Have it repaired by workshop

•

The hydraulic pressure

won't be increased

Insufficient engine RPM

•

Set the speed to 1.000 to 1.500 RPM

•

Insufficient transmission fluid

•

Add to the specified level

•

Air sucked into suction pipe

•

Tighten the connection. If any pipe or hose is

cracked or O-ring is damaged, replace it

•

Clogged oil filter

•

Clean

•

Defective hydraulic pump

•

Have it repaired by workshop

•

Defective valve

•

Have it repaired by workshop

•

Damaged cylinder

•

Have it repaired by workshop

•

RK19-영문-07(사).indd 7

2017-05-19 오전 9:48:59

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 118 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: