manualshive.com logo in svg

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 18 / 156

Share
Download
Rural King RK19 Hydrostatic Operator'S Manual Download Page 18

 - 1

SAFeTY PReCAUTIONS

T72O217A

Do not start the tractor in an en-

closed building unless the doors & 

windows are open for proper venti-

lation, as tractor fumes can cause 

sickness or death. If it is necessary 

to  run  an  engine  in  an  enclosed 

area remove the exhaust fumes by 

connecting exhaust pipe extension. 

WORK IN VeNTILATeD AReA

1. The tractor can start even if the 

transmission  is  engaged  posi-

tion causing tractor to runaway 

and  serious injury to the people 

standing nearby the tractor.

2. For additional safety keep the pull 

to stop knob (Fuel shut off con-

trol) in fully pulled out position.  

  Transmission in neutral position, 

Foot brake engaged and PTO le-

ver in disengaged position while 

attending to Safety Starter Switch 

or any other work on tractor. 

TRACTOR RUNAWAY

1. Brake operated safety switch is 

provided on all tractors which al-

low  the  starting  system  to  be-

come operational only when the 

Brake pedal is fully pressed.

2. Do not by-pass this safety starter 

switch or work on it. Only Autho-

rized RK Tractor store are recom-

mended  to work on safety starter 

switch. 

3. On some models Safety Starter 

switch is provided on transmis-

sion High-low shifter lever and in 

PTO shifter lever. The tractor can 

be started only if High-low shifter 

Safety Starter Switch is to be 

replaced  after  every  2.000 

hours/4  years,  whichever  is 

earlier.

•

CAUTION

SAFeTY STARTeR SWITCH

RK19-영문-01A(안).indd   17

2017-05-19   오전 9:41:25

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments